Avanti Studebaker Ford Dodge Jeep

'59-'66 Studebaker Lark Type
Coupes, Sedans, Wagons & Convertible


Studebaker lark

Floor Panels

Our Floor Panels are 22" wide and extend from the firewall seam to the rear seat riser in length. Our die stamped panel is manufactured in heavy 18 gauge steel and includes the seat anchor plates pre-attached.

 

Thresholds are properly formed and are arched front to rear just like the original floor panel, which will allow for proper Rocker Panel placement and the maintenance of original body shape and proper door fit upon completion.

 

We have paid close attention to original indent detail which is necessary for a proper repair or restoration. We have used original Studebaker archive prints in order to achieve a high degree of accuracy in our product.

 

3 pieces per side which includes joiner strip as shown.

1959-1960

$270.00 Driver Side

$270.00 Passenger Side

$520.00 Pair

More Information and Add to Cart Options

 

 

1961-1966

$270.00 Driver Side

$270.00 Passenger Side

$520.00 Pair

More Information and Add to Cart Options

1959-1960

    

Driver side                                Passenger side

1961-1966

                                                   

          

           

Driver side                                    Passenger side

Floor Mount Reinforcement Washers
'61-'66 Studebaker Lark Type, Sedan, Wagon and Convertible

Companion to Floor Panels shown above.Reinforces floor area where floor panel bolts to frame. There is a Driver and a Passenger, both are sides available.

$15.00 Driver

$15.00 Passenger

More Information and Add to Cart Options

 

Master Cylinder Access Cover

Can also be used as a gas tank sender unit cover.

$8.00 each

More Information and Add to Cart Options

Body Supports
Sedan, Wagon, and Convertible

Each Lark has six frame-to-body supports. Our supports are accurately reproduced in steel heavier than the original. If your original supports are rusted or overstressed due to metal thinning, your Lark will be more flexible than necessary.

$160.00 Body Support-Front Drivers

$160.00 Body Support-Front Passenger

$150.00 Body Support-Middle Drivers

$150.00 Body Support-Middle Passenger

$140.00 Body Support-Rear Drivers

$140.00 Body Support-Rear Passenger

$850.00 Body Support Set of Six (6)

More Information and Add to Cart Options


Rear of Front Fender Patches
Sedan, Wagon, and Convertible

Produced in 18-gauge steel. Front edge is flanged to allow flush fit. Rear of panel is rolled, as was original. Full length by 5" wide.

$75.00 Driver

$75.00 Passenger

More Information and Add to Cart Options

Rocker Panels
Sedan, Wagon, and Convertible

Our rocker panels have pre-formed weatherstrip channels and are properly arched from front to rear just like the originals which will allow for the maintenance of proper body shape, proper door fit and general ease of installation. Made of original gauge steel. Bolts are attached to all two-door types, as was original.

Rocker Panels 1959-1960   

2 Door shown-All 4 door types available.

$220.00 Set

More Information and Add to Cart Options

 

Rocker Panels 1961 Transition Year 

2 Door and 4 door types available.

$220.00 Set

More Information and Add to Cart Options

 

Rocker Panels 1962-1966

2 Door shown-All 4 door types available.

 

$220.00 Set

More Information and Add to Cart Options

 

59-60 2 Door shown - All 4 door types available.

 

61 Transition year 2 Door Shown - All 4 door types available

 

62-66 2 Door shown - All 4 door types available.

Trunk Panels
Sedan, Coupe, and Convertible

Our '62-'66 Studebaker trunk floors are manufactured in two overlaping pieces that allow for a frame-on and top down installation.  The trunk floors as shown can be made to work, with modification, on all '53-'61 types which are pretty much dimensionally the same.  Note the black marked lines on our panels and photo.  You may cut and elevate our panel in those areas as directed or cut the marked areas out if not needed.  As usual, our trunk floors are made in 18 gauge steel that was original to your Studebaker.

$340.00 each

More Information and Add to Cart Options

 

Trunk Patch Panels
Sedan, Coupe, and Convertible

$80.00 Driver

$80.00 Passenger

$160.00 Pair

More Information and Add to Cart Options

Studebaker rocker panel trim

Trunk Floor Corner Supports
Sedan, Coupe, and Convertible

Produced in steel heavier than the original. As with C/K types, shim to adjust door fit. The 59-60 are not exact copies but fit and work as they should.

$40.00 59-60 Driver

$40.00 59-60 Passenger

More Information and Add to Cart Options

$40.00 61-66 Driver

$40.00 61-66 Driver

More Information and Add to Cart Options

       

59-60 Driver           59-60 Passenger

61-66 Driver       61-66 Passenger

Spare Tire Washer Hold Down
Sedan, Coupe, and Convertible

$15.00

More Information and Add to Cart Options

 

Lower Door Skins
Sedan, Coupe, Wagon, and Convertible

Approximately 5"H x full length. Forward and bottom edges rolled as original. Rear edge left open to allow for proper installation. Upper edge is flanged for a flush fit.

$45.00 Driver

$45.00 Passenger

More Information and Add to Cart Options

Exhaust Hanger Bracket
Sedan, Coupe, and Convertible

Tailpipe hangers for all '53-'66 Studebaker CK/Hawk and Sedan types. Our hangers are produced in heavy 14 gauge steel and made in exact accordance to archive prints.

35.00 Exhaust Hanger Driver

$35.00 Exhaust Hanger Passenger

$70.00 Exhaust Hanger Pair

More Information and Add to Cart Options

 Studebaker rocker panel trim

Studebaker Quick Steering Arms

We have an amazing product for you!!   Steering rates that were built into your Studebaker in the '50's and '60's and into Avantis until the early '80's  were notoriously slow because of design tradition and general control resistence of original type bias ply tires.  Our quick steering arms along with your updated radial tires will make an impressive improvement to the handling qualities of your Stude or Avanti.  You will immediately notice a quicker steering response, better road feel, and a sharper turning radius.  Your Stude will handle more like a modern car guaranteed!  The quick steering arms are easily installed in a few hours and will fit any Stude or Avanti between the years of 1951-1982.  *Note that the quick steering arms are intended for use on all types of Studebakers with power steering.

$155.00 Quick Steering Arm Kit

More Information and Add to Cart Options

Studebaker rocker panel trim


*A personal note from the founder of Classic Enterprises---"Quick steering arms were installed on my personal Avanti and my '55 President Coupe.   I was thoroughly amazed and impressed by the difference it made.    Magic I say!!"

Studebaker Script Stamped Panel

Our heavy 16 gauge die stamped panel is ideal as a wall hanging in a Man Cave, a patio bench backrest, a panel for the face of an office desk, or as an overlay for a damaged original Stude pickup tailgate.  Our panel size is 16" X  48".  The quality of our stamping is exceptional.

250.00 Script Stamping

More Information and Add to Cart Options