'54-75' Jeep CJ6 | Willys M170
_____Floor_____
Side and Cowl Area
____Supports____
__Tail/Rear Area__
___Wheel Area___
_______All_______
Gifts and Misc.
CJ6 Rear Floor Extension Braces
These braces support the Rear Floor Extension, the floor panel that is placed between the rear floor and the seat area
- Diagonal/Outer Brace is 18 Gauge Steel
- Inner Brace is 16 Gauge Stee
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$200.00 Set of Four
CJ6 Side Panel Extension
- 18 gauge steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$215.00 Driver
$215.00 Passenger
$430.00 Pair
Rear Corner Lower Repair Section
Exposed surface approximately 12 inches tall, when measuring from lower edge to bottom of flanged area. The section covers the spare tire support, a typical problem area for rust.
- 18 gauge steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$100.00 Pair
Rear Side Panel Section Top Bow Indent
- 18 gauge steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$95.00 Driver
$95.00 Passenger
$190.00 Pair
"JEEP" Stamped Side Repair Panel
The upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances. The forward, upper, rear and lower edges of our panel are a duplication of the original.
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$145.00 Driver
$145.00 Passenger
$290.00 Pair
Side Repair Strip
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$65.00 Driver
$65.00 Passenger
$130.00 Pair
Cowl Repair Clip
Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation.
Overlap reinforcement included at the front of each panel where it bolts to the fender. We do not pre-drill the mounting holes in the reinforcement. The installer will drill his own holes and thus will have the flexibility to adjust for any modifications or variations encountered during installation.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Cowl Area Body Reinforcement
- Die Formed
- 14 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$60.00 Driver
$60.00 Passenger
Cowl Area Reinforcement Lower Repair Section
- Die Formed
- 14 Gauge Steel
- 10 inches tall
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$75.00 Driver
$75.00 Passenger
$150.00 Pair
Firewall / ToeBoard Body Supports
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
More information and Add to Cart Options
'54-'71 Jeep CJ6, M170 Floor Panels
The length of the panel is from the rear floor riser forward to the toe board area with an approximate 2" roll up. The outside edge of our panel is properly formed downward to attach to the side panel as was original to the vehicle. We have provided an extra 2" of material at the transmission tunnel area which you can roll up if needed or trim off if not needed. Our passenger side floor panel does provide for the floor of the toolbox.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$70.00 Driver
$70.00 Passenger
$140.00 Pair
'72-75' Jeep CJ6 M170 Floor Panels
The length of the panel is from the rear floor riser forward to the toe board area with an approximate 2" roll up. The outside edge of our panel is properly formed downward to attach to the side panel as was original to the vehicle. We have provided an extra 2" of material at the transmission tunnel area which you can roll up if needed or trim off if not needed. Our passenger side floor panel does provide for the floor of the toolbox.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$70.00 Driver
$70.00 Passenger
$140.00 Pair
'55-'75 Jeep CJ6, M171 Floor Body Supports
Original early CJ5 Jeep floor supports have either a square tubing or a channel support element that fits under the driver firewall support. Either type should be compatible with any CJ5 or CJ6 Jeep type. Be sure to specify "tube type" or "channel type" when ordering.
- 16 Gauge Steel
- Pipe Stand-offs used in bolt-down areas, rather than the original wood crush blocks.
- Floor Support Joiners sold separately.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in USA
$90.00 Driver
$90.00 Passenger
$180.00 Pair
Front Floor Support Joiner
Made for later types not needing an emergency brake spring return retainer. Companion to floor supports shown above. Shown upside-down for illustrative purposes.
- Die Stamped
- 16 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$25.00 each
Rear Floor Riser
Die formed in steel heavier than the original with Frame Mounts attached.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$95.00 each
Rear Floor
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$350.00 each
Wheelhouse
- All ribs and outboard edges are die formed.
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$185.00 Driver
$185.00 Passenger
$370.00 Pair
Sparetire and Corner Reinforcement
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
'51-71' Jeep CJ6, M170 Passenger Wheelhouse Support Baffle
Note that the baffel shown at the right is a very good representation of the original factory issued Jeep baffel which was somewhat crude in its original concept and construction.
- Die Formed
- 11 1/2" x 12 1/4"
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$105.00 Passenger
More information and Add to Cart Options
1941-1975 WILLYS Jeep CJ6, M170 Driver Wheelhouse Support
Our CJ5 & CJ6 support channel is a 2" wider version of the CJ2-3 type. The extra width is provided by our 2" joiner which is securely and neatly spot-welded into place. Our support channel is thus not a 100% accurate reproduction for the purist restorer, but is nevertheless completely functional for its intended application. (Our CJ 7 baffel will also fit and do the same job.)
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 Driver
External Wheelhouse Angle Support
Connects and reinforces area between leading face of Wheelhouse & inboard face of side panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$25.00 each
$50.00 pair
Wheel Arch Area Repair Panel
Properly gauged steel. 2 1/4" exposed face with a flanged edge for a flush fit for welding. The wheel side edge is properly rolled inward as was original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 Driver
$115.00 Passenger
$230.00 Pair
End Panels for Military & Custom Types
Eliminates tail light panels & tail gate. All structural bracing & hardware attached to our panels via appropriate spot welds. Spot welds cosmetically covered for our photographic & display purposes. Military Panel has four vertical supports.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
(17 3/4" x 50")
$425.00 each
Rear Frame Crossmember & Stiffener Insert Body Support
- Die Formed and Punched
- Properly Gauged
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$135.00 each
Tailgate Opening Surround
Properly gauged and designed for a proper fit.
- Chain Hook Eyes attached.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 each
More information and Add to Cart Options
Tail Light Panel
Tail Light Panel
Properly die formed in 18 gauge steel as was original. Yes, all edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00Driver
$35.00Passenger
$70.00 Pair
More information and Add to Cart Options
Tail Light Panel Rear Body Angle Support
Produced in heavy 16 gauge steel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$10.00 each
$20 pair
More information and Add to Cart Options
Tail Light Panel With Body Angle Support Attached
Properly die formed in 18 gauge steel as was original. Yes, all edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00Driver
$55.00Passenger
$110.00 Pair
Rear Valence Panel
All edges are properly formed as was original.
- Die Formed
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
Rear Valence Angle Body Support
- 16 Gauge Steel (Heavier than original.)
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$10.00 each
$20.00 pair
Rear Valence Panel with Body Supports Attached
Jeep Rear Valence Panel & Angle Supports as a unit, Produced in original gauge steel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$85.00 each
Willys Stamped Patch Panel
Same lettering and scale as originally stamped into CJ2A windshield panel. Hood stamping patch and military WILLYS end panel patch is available upon special request.
- 6" x 8 1/4"
- Stamped into 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 WILLYS Stamp
