'41-'64 Willys Jeep MB, CJ2A, 3A, 3B, M38
Floor
Front Area
Side and Cowl Area
Supports
Tail/Rear Area
Wheel Area
Other
All
Gifts and Misc.
Select a link below:
Front Bumper
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$125.00
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$125.00
Hood - WILLYS Stamped
- WILLYS Stamping, Rolled Edges, and Center Seam constructed to match original design.
- Includes Pre-Attached Hinge and Support, based on later model years' styling.
- Does Not include Latch or Latch Hardware
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$850
Front Fender Angle Supports
Exceptional front fender angle supports for all "flat fender" type Jeeps.
Note, we use pipe stand-offs in bolt-down areas rather than the original wood crush blocks. This makes a stronger and more durable product.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 Driver
$45.00 Passenger
$90.00 Pair
Driver Passenger
Windshield Panels
Willys Jeep MB, GPW
Our military windshield panels are properly gauged and die-formed in order to provide you with a quality and accurately authentic product. We think that you will be pleased with what you receive.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$95.00 Unstamped
Windshield Panels
Willys Jeep CJ2A
- Die Stamped
- Approved by FCA US LLC
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$150.00 WILLYS Stamped
Step Tread
- Die Stamped
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Front Panel
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$155.00 Driver with Drain Hole
$155.00 Passenger with Drain Hole
$310.00 Pair with Drain Hole
More Information and Add to Cart Options
$155.00 Driver Without Drain Hole
$155.00 Passenger Without Drain Hole
$310.00 Pair Without Drain Hole
A. Front Panel
Set of four includes both rears and both fronts
$795.00 Full Set of Four
More Information and Add to Cart Options
Fender to Cowl, Firewall Support Bracket
This is a very hard to find support bracket that hooks the fender to the firewall and to the cowl. This gives strength to an area prone to vibration. Our bracket is die formed out of original gauge steel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 Driver
$35.00 Passenger
$70.00 Pair
Cowl and Body Area Reinforcements
Nicely die formed in heavy 14 Gauge Steel. This can be used on the lower part pf the CJ3B.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$60.00 Driver
$60.00 Passenger
$120.00 Pair
Firewall / ToeBoard Body Supports
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Side Panel Joiner Gusset
Front & Rear Side Panel Joiner Gusset
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$20.00 each
$40.00 pair
Rear Corner Lower Repair Section
Exposed surface approximately 12 inches tall, when measuring from lower edge to bottom of flanged area. The section covers the spare tire support, a typical problem area for rust.
- 18 gauge steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$100.00 Pair
Rear Quarter Side Panel
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$250.00 Driver Side
$250.00 Passenger Side
$500.00 Pair
Set of four includes both rears and both fronts
$795.00 Full Set of Four
Lower Side Repair Strip
Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original. Exposed face surface 4" high.
- Formed in 18 gauge steel
- Exposed face surface 4" high
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$30.00 Driver
$30.00 Passenger
$60.00 Pair
Civilian Seat Back
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 each
$70.00 pair
Military Seat Back
Military Seat Back, two ribs.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 each
$70.00 pair
Military Seat Base Panels
Willys Jeep MB
Military Driver Side and Passenger Side. Approximate dimensions are 18 1/2 X 15 1/8.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
Driver Passenger
Seat Base Panels
Willys Jeep CJ2A, CJ3A and CJ3B
Our civilian type seat base panels now have appropriate upholstery claws just like the originals. Approximate dimensions are 18 1/2" x 15 1/8".
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 each
More Information and Add to Cart Options
Driver Passenger
With Upolstery Claws
Seat Base Panels
Willys Jeep CJ2A, CJ3A, CJ3B and MB
Civilian Driver and Passenger Side and Military Driver and Passenger Side. Approximate dimensions are 18 1/2 X 15 1/8.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
Driver Passenger
No Upholstery Claws
Willys Jeep Toolbox
Forward And Inboard Face Repair Panels
Toolbox forward and inboard face repair panels.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$25.00 Forward Toolbox Face
$15.00 Inboard Toolbox Face
More Information and Add to Cart Options
FORWARD TOOLBOX FACE
INBOARD TOOLBOX FACE
Floor Panels
The length of the panel is from the rear floor riser forward to the toe board area with an approximate 2" roll up. The outside edge of our panel is properly formed downward to attach to the side panel as was original to the vehicle. We have provided an extra 2" of material at the transmission tunnel area which you can roll up if needed or trim off if not needed. Note that an original type side panel drain hole well has now been added to our floor panels. Our passenger side floor panel does provide for the floor of the toolbox.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$70.00 Driver
$70.00 Passenger
$140.00 Pair
Driver Passenger
Master Cylinder Cover
1946-1964 Willys Jeep CJ2A, 3A, 3B, M38
- Die Formed
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$15.00 Master Cylinder Cover
Floor Body Supports
1946-1964 Willys Jeep CJ2A, 3A, 3B, M38
- 16 Gauge Steel
- Pipe Stand-offs used in bolt-down areas, rather than the original wood crush blocks.
- Floor Support Joiners sold separately.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$90.00 Driver
$90.00 Passenger
$180.00 Pair
Front Floor Support Joiner
Made for early types needing an emergency brake spring return retainer. Companion to floor supports shown above.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 each
Rear Floor Riser
- Die Formed
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$85.00 each
Rear Floor
1946-1964 Willys Jeep CJ2A, 3A, 3B, M38
Strict attention is paid to crisp stamping detail and general panel appearance and accuracy for the CJ2A. This panel will fit the 3A, 3B and M38 but the front indents are forward approximently 3 inches. Our main panel is properly gauged. Our attached floor supports are over-gauged which will provide you with a much tougher and durable panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$350.00 each
More Information and Add to Cart Options
Wheelhouse
Our wheelhouses are of exceptional quality and made in properly gauged steel. All ribs and outboard edges are die formed for proper appearance and detail to accuracy. Our wheelhouses are sized for an exact fit during your installation.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$185.00 Driver
$185.00 Passenger
$370.00 Pair
More Information and Add to Cart Options
You can also buy our top and front only. All ribs and outboard edges are die formed for proper appearance and detail to accuracy.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$135.00 Driver
$135.00 Passenger
$270.00 Pair
Sparetire and Corner Reinforcement
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
Wheelhouse Support Baffle
Passenger Side Wheelhouse Baffel and Corner Reinforcement.
- Die Formed
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$105.00 Passenger
Wheelhouse Support
CJ2 Internal Wheelhouse Channel Support for Driver Side
- Die Formed
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 Driver
External Wheelhouse Angle Support
1941-1949 Willys Jeep CJ2A
Connects & reinforces area between leading face of Wheelhouse & inboard face of side panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$25.00 each
$50.00 pair
External Wheelhouse Support
1949-1964 Willys Jeep 3A, 3B, M38
WILLYS Jeep CJ3 & later External Wheel-house Angle Support
Connects & reinforces area between leading face of Wheelhouse & inboard face of side panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$25.00 each
$50.00 Pair
Wheel Arch Area Repair Panel
2 1/4" exposed face with a flanged edge for a flush fit for welding. The wheel side edge is properly rolled inward as was original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 Driver
$115.00 Passenger
$230.00 Pair
Military End Panel
Eliminates tail light panels and tail gate. All structural bracing and hardware are attached to our panels via appropriate spot welds.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$425.00 each
Large WILLYS Stamping
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 Large WILLYS Stamp
Small WILLYS Stamping
Small WILLYS Stamped lettering on a 7" X 10" metal plate in 18 gauge steel with a lettering dimension of 6 1/2" X 1 1/2". (Same as windshield panel and hood stamping.)
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 Small WILLYS Stamp
Rear Frame Crossmember Body Support
With Stiffiner Insert
Our rear frame crossmember is made from properly gauged American steel, die formed and punched. Our price includes the rear stiffiner insert.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$135.00 each
More Information and Add to Cart Options
Tailgate Opening Surround
- Chain hook eyes attatched.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 each
Tail Light Panel
Tail Light Panel
All edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options.
- Die Formed
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$35.00 Driver
$35.00 Passenger
$70.00 Pair
More Information and Add to Cart Options
Tail Light Panel Rear Body Angle Support
- Heavy 16 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$10.00 each
$20.00 pair
More Information and Add to Cart Options
Tail Light Panel With Angle Body Support Attached
Panels are not drilled or punched which allows the installer various tail light placement options.
- Die Formed
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
More Information and Add to Cart Options
Tail Light Panel With Custom Recess Hole
Tail Light Panel
Properly die formed in 18 gauge steel as was original. All edges are properly formed as was original. Panels have a custom 4 1/2 inch diameter hole and reinforcement to recess mount your tailights. This helps to decrease trail damage.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$60.00 Driver
$60.00 Passenger
$120.00 Pair
More Information and Add to Cart Options
Tail Light Panel with Angle Support AttatchedProperly die formed in 18 gauge steel as was original. All edges are properly formed as was original. Panels have a custom 4 1/2 inch diameter hole and reinforcement to recess mount your tailights. This helps to decrease trail damage.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$80.00 Driver
$80.00 Passenger
$160.00 Pair
Taillight Panel With Taillight Hole and Body Support
Willys Jeep M38 M606
Panels have the correct 5 inch diameter hole punched and the taillight bracket that also works as the rear support is attatched. Also includes the upper edge reinforcement attatched which protrudes approximately one inch for secure attatchment into your corner.
- Die Formed
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$85.00 Driver
$110.00 Driver with Trailer Plug Mounting
$85.00 Passenger
Taillight Bracket Rear Body Support
Willys Jeep M38, M606
Our Military taillight bracket rear support is produced in properly 18 gauged steel. All holes are properly punched.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 Driver
$45.00 Passenger
$90.00 Pair
Rear Valence Panel
- Die Formed
- 18 Gauge Steel
- All edges properly formed as was original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$45.00 each
Rear Valence Angle Body Support
Produced in 16 gauge steel. Heavier than original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$10.00 each
$20.00 pair
Rear Valence Panel with Body Supports Attatched
Jeep Rear Valence Panel with Angle Body Supports as a unit.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$85.00 each
Keychain
- Approximately 1" x 4"
- Includes Key Ring
- 12 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$15
