Studebaker '47-'52 Sedans
Coupes & Convertibles
Floor
Side and Cowl Area
Supports
Tail/Rear Area
Wheel Area
Other
All
Gifts and Misc.
Rocker Panel Trim Moldings
You might also consider that our moldings would be a great addition to your unadorned Stude and will definitely add a lot of extra snap and class to the look of an already cool-looking car.
Molding clips and installation instructions are included.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$525.00 47-52 2 and 4 Door Stainless Rocker Moldings Pair
$525.00 47-50 Land Cruiser Stainless Rocker Moldings Pair
$150.00 Cruiser Stainless Spear Points Pair
Floor Panels
Our Floor Panels are 22" wide and extend from the firewall seam to the rear seat riser in length. Our die stamped panel is manufactured in heavy 18 gauge steel and includes the seat anchor plates pre-attached.
Our Floor Panel thresholds are properly formed and are arched front to rear just like the original floor panel which will allow for proper Rocker Panel placement and the maintenance of original body shape and proper door fit upon completion.
We have paid close attention to original indent detail which is necessary for a proper repair or restoration. We have used original Studebaker archive prints in order to achieve a high degree of accuracy in our product
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$270.00 Driver Side
$270.00 Passenger Side
$520.00 Pair
Master Cylinder Access Cover
Can also be used as a gas tank sender unit cover.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$8.00 each
Body Supports
Our Supports are produced in steel heavier than the original. There are three body supports per side, which were originally spot-welded to the floor panels and bolted to the frame.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$170.00 Driver Front
$170.00 Passenger Front
$160.00 Driver Middle
$160.00 Passenger Middle
$150.00 Driver Rear
$150.00 Passenger Rear
$875.00Set Of Six (6)
Trunk Panel
'50-'52 Studebaker Sedans, Coupes and Convertible
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$320.00 each
Spare Tire Wheel Well
'50-'52 Studebaker Sedans, Coupes and Convertibles
Our spare tire well is a perfect reproduction in rust-proof fiberglass. (Companion to trunk panel shown above.)
$175.00 each
More Information and Add to Cart Options
Spare Tire Washer
Spare Tire Hold Down Washer - 6" DIA
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$15.00 Spare Tire Washer Hold Down
Lower Door Skins
Approximately 5" H x full length. Forward and bottom edges rolled as original. Rear edge left open to allow for proper installation. Upper edge is flanged for a flush fit.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
2 Door - $55.00 each
4 Door - $50.00 each
Rocker Panels
Our rocker panels have pre-formed weatherstrip channels and are properly arched from front to rear just like the originals which will allow for the maintenance of proper body shape, proper door fit and general ease of installation. Made of original gauge steel.
Bolts are attached to all two-door types as was original.
Ends are properly die formed as is true of all our rocker panels.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$245.00 2 Door Pair
$220.00 4 Door Pair
$220.00 Cruiser Pair
2 Door shown-All 4 door types available.
Vent Patch
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$85.00 each
More Information and Add to Cart Options
Hinge and Shroud Collar
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$85.00 each
More Information and Add to Cart Options
Vent Patch and Hinge & Shroud Collar Attached
Both products are securely spot welded together which will allow for faster installation. (Can be special ordered without perimeter flange.)
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$185.00 each
More Information and Add to Cart Options
Vent Shrouds
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$160.00 Per Car
Studebaker Script Stamped Panel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$250.00 Script Stamping
