Avanti Studebaker Ford Dodge Jeep

'51 - '71 Jeep CJ5 | Willys M38A1

Patch Panel

$35.00

More Information and Add to Cart Options

Keychain

  • Approximately 1" x 3"
  • Includes Key Ring
  • 12 Gauge Steel
  • None of our panels are cosmetically coated. Click here to find out why.
  • Made in the USA

$15.00

More Information and Add to Cart Options

Rear Side Panel Section Top Bow Indent

The indented section of the rear side panel, originally intended for the top bow. Support channel insert for upper curl is included.

$95.00 Driver

$95.00 Passenger

$190.00 Pair

More Information and Add to Cart Options

Rear Corner Lower Repair Section

Forward edge formed to fit wheel arch as original. Bottom edge formed at 90° angle. Flanged upper edge for welding purposes. Rear is curved, then formed at 90º angle, to properly meet the tail light panel.

Exposed surface approximately 12 inches tall, when measuring from lower edge to bottom of flanged area. The section covers the spare tire support, a typical problem area for rust.

$55.00 Driver

$55.00 Passenger

$100.00 Pair

More Information and Add to Cart Options

2 Piece Side Repair

Our 2 piece side repair kit has a crisp "Jeep" stamped front quarter panel, and the rear quarter panel. They are designed to work together to form a complete side repair. Both are made in 18 gauge steel here in our plant. The rear 1/4 (panel B) has the rear 900 bend where it meets the corner and the upper edge is flanged so you can weld to your original tub edge. The wheel opening has a finished edge. Panel B is flanged where it meets panel A for a smooth fit.

$145.00 Front Quarter Side Repair Panel A

$155.00 Rear Quarter Side Repair Panel B

More Information and Add to Cart Options

"JEEP" Stamped Side Repair

Authentically Stamped "JEEP" Side Panel Repair Clips. The upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances. The forward, upper, rear and lower edges of our panel are a duplication of the original.

$145.00 Driver

$145.00 Passenger

$290.00 Pair

More Information and Add to Cart Options


Lower Side Repair Strip

Our panel is formed with a  flanged upper edge that allows for a flush fit for welding purposes. The length of our panel begins with a 900 fold at the front fender seam and ends with the formed wheel arch area as original. The exposed face surface is 4" high.

$50.00 Driver

$50.00 Passenger

$100.00 Pair

More Information and Add to Cart Options


"JEEP" Stamped Cowl Repair Clip

Top, front & bottom edges are formed like the original panel.  Rear edge is flanged to form a flush fit during installation.

$55.00 Driver

$55.00 Pass

$110.00 Pair

More Information and Add to Cart Options


jeep-cowl-clip-support
 

Cowl Area Body Reinforcements

Jeep Cowl Area Reinforcement

$60.00 Driver

$60.00 Passenger

$120.00 Pair

More Information and Add to Cart Options

 

   

Cowl Area Reinforcement Lower Repair Section

$75.00 Driver

$75.00  Passenger

$150.00 Pair

More Information and Add to Cart Options

 Studebaker rocker panel trim

Firewall / ToeBoard Body Supports

Exceptional quality firewall/toeboard body supports for your Jeep.

$55.00 Driver

$55.00 Passenger

$110.00 Pair

More Information and Add to Cart Options


Floor Panels

The length of the panel is from the rear floor riser forward to the toe board area with an approximate 2" roll up. The outside edge of our panel is formed downward to attach to the side panel as was original to the vehicle.

We have provided an extra 2" of material at the transmission tunnel area which you can roll up if needed or trim off if not needed.  Our passenger side floor panel does provide for the floor of the toolbox.

$70.00 Driver

$70.00 Passenger

$140.00 Pair

More Information and Add to Cart Options

Floor Body Supports

$90.00 Driver

$90.00 Passenger

$180.00 Pair

More Information and Add to Cart Options

 

Some early CJ5 Jeep floor supports have a square tubing support element that fits under the driver firewall support. If your Jeep has this, you can use the option below to order the "tube type". (Sometimes the Jeep engineers did mysterious things.)

"Square-tube" style is usually found on 6 or 8 cylinder models.

$90.00 Driver (Square Tube Style)

$90.00 Passenger

$180.00 Pair  (Square Tube Style)

More Information and Add to Cart Options

 

Front Floor Support Joiner

Made for later types not needing an emergency brake spring return retainer. Companion to floor supports above.

$25.00 each

More Information and Add to Cart Options

no brake

Rear Floor Riser

Die formed in steel heavier than the original with Frame Mounts attached.

$95.00 each

More Information and Add to Cart Options

 

Rear Floor

Our newest generation of rear floor panels are now manufactured using updated patterns and dies. Strict attention is paid to crisp stamping detail and general panel appearance and accuracy. Our main panel is properly American gauged. Our attached floor supports are over-gauged which will provide you with a much tougher and durable panel.

$350.00 each

More Information and Add to Cart Options

Wheelhouse

  • All ribs and outboard edges are die formed.
  • 18 Gauge Steel
  • None of our panels are cosmetically coated. Click here to find out why.
  • Made in the USA

$185.00 Driver

$185.00 Passenger

$370.00 Pair

More Information and Add to Cart Options

Sparetire and Corner Reinforcement

Our channel reinforcement is made in properly gauged steel and will attatch to your original passenger side wheelhouse baffel.

$45.00 each

More Information and Add to Cart Options

 

Passenger Wheelhouse Support Baffle

Our baffel is a very good representation of the original factory issued Jeep baffel, which was somewhat crude in its original concept and construction.

$105.00 Passenger

More Information and Add to Cart Options

 

Driver Wheelhouse Support

Our CJ5  support channel is a 2" wider version of the CJ2-3 type.  The extra width is provided by our 2" joiner which is securely and neatly spot-welded into place.  You will note that our support channel is thus not a 100% accurate reproduction for the purist restorer but is nevertheless completely functional for its intended application.  (Our CJ 7 baffel will also fit and do the same job.)

$45.00 Driver

More Information and Add to Cart Options

jeep cj5 wheelhouse support driver side

WILLYS Stamped Patch Panel

Same lettering and scale as originally stamped into CJ2A windshield panel. Hood stamping patch and military WILLYS end panel patch is available upon special request.

$35.00 WILLYS Stamp

More Information and Add to Cart Options

External Wheelhouse Angle Support

Connects & reinforces area between leading face of Wheelhouse & inboard face of side panel.

$25.00 each

$50.00 pair

More Information and Add to Cart Options

Wheel Arch Area Repair Panel

2 1/4" exposed face with a flanged edge for a flush fit for welding. The wheel side edge is properly rolled inward as was original.

$115.00 Driver

$115.00 Passenger

$230.00 Pair

More Information and Add to Cart Options

flare

'51-71' Jeep CJ5, '51-62' M38A1, End Panels

Military M38A1 Jeep End Panel

Our new end panel is made to exacting specifications for the M38A1 military Jeep but can be used on all non-tailgate types with a 17 3/4" x 50" panel opening.  Our panel is a restoration quality product and completely American made in our facility with properly gauged Americal steel.  All holes are properly punched and all supports are part of the panel.   Likewise all stationary nuts and loops have been properly installed for a completely authentic look.

 $495.00 each

More Information and Add to Cart Options

 

CJ5 Civilian Jeep End Panel, No Taillight Cutouts

17 3/4" x 50"

$425.00 each

More Information and Add to Cart Options

 

Inside View Shows Supports On M38A1

___________________________________

Inside view of CJ5

Rear Frame Crossmember Body Support with Stiffener Insert

Properly gauged steel, die formed and punched.

$135.00 each

More Information and Add to Cart Options

                             

Tailgate Opening Surround

Properly gauged and redesigned for a proper fit. Chain hook eyes attached!

$115.00 each

More Information and Add to Cart Options

'51-'62 M38-A1 Taillight Bracket Rear Body Support

Our Military taillight bracket rear support is produced in 18 gauge steel.  All holes are properly punched.

$45.00 Driver

$45.00 Passenger

$90.00 Pair

More Information and Add to Cart Options

  Studebaker rocker panel trim

Tail Light Panel

Tail Light Panel

Die formed in 18 gauge steel as was original. All edges are properly formed as was original. Panels are not drilled or punched, which allows the installer various tail light placement options.

$35.00Driver

$35.00Passenger

$70.00 Pair

More Information and Add to Cart Options

Tail Light Panel Rear Body Angle Support

Produced in heavy 16 gauge steel.

$10.00 each

$20 pair

More Information and Add to Cart Options

Tail Light Panel With Body Angle Support Attached

Die formed in 18 gauge steel as was original. All edges are properly formed as was original. Panels are not drilled or punched which allows the installer various tail light placement options.    

$55.00Driver

$55.00Passenger

$110.00 Pair

More Information and Add to Cart Options



Rear Valence Panel

All edges are properly formed as was original.

$45.00 each

More Information and Add to Cart Options

Rear Valence Body Angle Support

Produced in 16 gauge steel. Heavier than original.

$10.00 each

$20.00 pair

More Information and Add to Cart Options

Rear Valence Panel with Body Angle Supports Attatched

Jeep Rear Valence Panel. Angle Supports as a unit. Produced in original gauge steel.

$85.00 each

More Information and Add to Cart Options

 

A Classic Jeep Commercial