'81-'86 Jeep Scrambler CJ8
_____Floor_____
___Front Area___
Side and Cowl Area
____Supports____
__Tail/Rear Area__
___Wheel Area___
_______All_______
Gifts and Misc.
Front of Vehicle Diagram
Keychain
- Includes Key Ring
- 12 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$15 each
Rear Corner Tail Light Panel Section
Bottom edge formed at 90° angle. Flanged upper edge for welding purposes. Rear is curved, then formed at 90º angle, to properly meet the tail light panel.
Exposed surface approximately 17-3/4 inches tall, when measuring from lower edge to bottom of flanged area.
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55 Driver
$55 Passenger
$100 Pair
Front Floor Panels
Our extended width floor panels are available in properly gauged steel. Our panels are accurately die stamped as a full length panel that spans the distance from the firewall seam to the rear floor riser as one continuous panel.
A one piece panel makes for fewer fitting and alignment problems and less welding and warpage during installation.
The outside edges of our panels are folded down as was original. The inboard edges are folded properly upward to follow the transmission tunnel curvatures as shown in our photo. We do not drill or punch any holes other than the two per panel as shown in the photos at the right. We have found that our customers prefer to drill their own according to their need and preference.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$180.00 Driver
$180.00 Passenger
$360.00 Pair
Foot Area Repair Clip
Outside edge is rolled down as was original.
- Die Stamped
- 18 Gauge Steel
- Approx 16" Wide
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Foot Area Repair Clip Driver
$55.00 Foot Area Repair Clip Passenger
$110.00 Foot Area Repair Clip Pair
Rear of Front Floor Repair
The outside edge is rolled down as was original.
- Die Stamped
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Drivers
$55.00 Passenger
$110.00 Pair
Toe Board Front Floor Body Supports
All captured nuts and studs attatched.
A superior product that is manufactured to original factory gauged steel, size and standards.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$95.00 Driver
$95.00 Passenger
$190.00 Pair
Full Width One Piece Traverse Body Supports
Installation can be accomplished by rear drive shaft and/or exhaust pipe removal in some instances. A one piece traverse support is sure to save you considerable cutting, alignment, welding time and alleviate a lot of general installation frustration as well.
- All appropriate nut blocks and cages pre-attached as was original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$175.00 each
Driver and/or Passenger Traverse Body Supports
As usual these products are properly gauged, with appropriate caged nuts that are pre-installed for your convenience.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$115.00 Driver Side
$115.00 Passenger Side
Outboard Rail Floor Body Support
- Die Formed in Steel Heavier Than the Original
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Outboard Rail Driver
$55.00 Outboard Rail Passenger
$110.00 Pair
Inboard Rail Floor Body Support
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Inboard Rail Driver
$55.00 Inboard Rail Passenger
$110.00 Pair
More Information and Add to Cart Options
"Jeep" Stamped Side Panel
The upper edge of our panel is flanged to allow for a flush fit when clamping against your cut along the driver and passenger side entrances.
The Jeep stamped lettering is exact in accordance to our original sample panel and approved by FCA LLC.
The forward, upper, rear and lower edges of our panel are a duplication of the original.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$165.00 Driver Side
$165.00 Passenger Side
$330.00 Pair
Lower Repair Strip
Flanged upper edge allows for a flush fit for welding purposes. Bottom of panel and wheel arch area are properly formed like original.
- 18 Gauge Steel
- Exposed face surface 6 1/2" high
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$75.00 Driver
$75.00 Passenger
$150.00 Pair
"JEEP" Stamped Cowl Area Repair Clip
Top, front & bottom edges are formed like the original panel. Rear edge is flanged to form a flush fit during installation.
Original type reinforcement attached to the front of each panel where it bolts to the fender.
We do not pre-drill the mounting holes in the reinforcement. The installer will drill his own holes and thus will have the flexibility to adjust for any modifications or variations encountered during installation.
- 17 1/4" High X 12" Wide
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Door Skin
Side and bottom edges are bent at 90o and the top is flanged for an easier installation. Approximately 6-1/4 inch height, plus a 1/2 inch flange, and is full width.
- 18 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$50.00 Driver
$50.00 Passenger
$100.00 Pair
Cowl Area Body Reinforcements
Jeep Cowl Area Reinforcement for all 1976-1995 Types
- Die Formed
- Heavy-Duty 14 Gauge Steel
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$60.00 Drivers
$60.00 Passenger
Cowl Area Reinforcement Lower Repair Section
- Die Formed
- Heavy-Duty 14 Gauge Steel
- 10 Inches Tall
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$75.00 Driver
$75.00 Passenger
$150.00 Pair
B Pillar, Door Latch Support, Latch Pillar Repair
Note that the lower baffel is pre-installed in its proper position.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$55.00 Driver
$55.00 Passenger
$110.00 Pair
Rear of Vehicle Diagram
Rear Floor Riser
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$145.00 each
Front View
Top View
Rear Floor
Strict attention is paid to crisp stamping detail and general panel appearance and accuracy.
Our main panel is properly American gauged. Our attached floor supports are over-gauged which will provide you with a much tougher and more durable panel.
All appropriate threaded fasteners are attached as they were on the original panel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$490.00 each*
*There is an additional $95.00 UPS oversize surcharge that is added to our standard shipping charge.
Rear Floor Corner Panels
Front of Jeep rear floor corner panels and Rear of Jeep rear floor corner panels.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$40.00 Driver Front
$40.00 Passenger Front
$40.00 Driver Rear
$40.00 Passenger Rear
$160.00 All Four
Rear Wheel House
All ribs and outboard edges are die formed for proper appearance and detail accuracy. Our wheelhouses are sized for an exact fit during your installation.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$185.00 Driver
$185.00 Passenger
$370.00 Pair
Rear Floor Support
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$105.00 Each
Tailgate End Body Support
Tailgate end supports are intended to attach the body to the frame via a body bolt at each end of the support.
Our product is a very close representation of what was original to your Jeep.
It is properly factory gauged and die formed with all captured nuts brought to original factory size and standard. We have paid very close attention to quality and detail and thus have an exceptional product for you.
*Our end supports can also be ordered for use on types that do not have tailgates.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$215.00 Each
More Information and Add to Cart Options
Rear Frame Crossmember Body Support
Perfectly detail cut & formed in original gauge steel.
- None of our panels are cosmetically coated. Click here to find out why.
- Made in the USA
$135 Rear Frame Crossmember
Custom Flush Mount Taillights
$80.00 each
$160.00 pair
